8" Pitless Booster

Click the image to view full size

Features
Specifications
Parts Breakdown
Ordering Instructions

EASY ACCESS TO SERVICE... Well cap can be removed without disconnecting cables. O-ring seals on spool permit withdrawal of the entire inner assembly simply by lifting. Replacement is equally simple. Spool support eliminates vertical adjustment allowing service above ground.

CORROSION PROTECTION... Spool and Discharge Body are either lead free hot-dipped galvanized or constructed of corrosion resistant material for longer life, less service.

RELIABLE SEAL... Neoprene O-rings between accurately machined lead free hot-dipped galvanized surfaces on the spool and within the unit provide positive seals to ensure maintenance free performance.

O-RING SEAL PROTECTION... Monitor seal protection prevents seal damage during installation and service eliminating potential service costs.

QUICK TO INSTALL... A quality booster pump installation can be made easily and economically without delay for masonry or building construction creating a sound cost savings solution.

ALTERNATIVE SPOOLS (6x7 and 8x10 only)... Spools are available plain or with silent check valves. The Monitor silent check valve has its operating parts automatically exposed when the spool is withdrawn. Spools are supplied with tappings for pressure controls.

WATERTIGHT WELL CAP... Designed to permit removal without disconnecting cables. Watertight cable and conduit sealing is available for additional protection.

HOLD DOWN... Supplied with each unit. Hold-down pipe also serves as lift-out pipe for installation and allowing speedy service.

FROST PROOF... No heating is required. All water passages are below the frost line.

ALTERNATIVE DISCHARGE & INLET CONNECTIONS... Are available to meet your requirements.

A	Seal Cap: The Watertight cap bolts to a compression seal ring securing around the pitless case and comes with the screened well vent installed.
B	Conduit Tapping size: Watertight conduit seals for most common cable sizes are available for watertight cap.	1-1/2” NPT
C	Distance from ground level to top of Pitless Case	12"
D	Distance from ground level to top of Well Cap	14-3/4"
E	Pitless Case size	6"
F	Pitless Case wall thickness	280"
G	"Hold Down-Lift Out Assembly": positions & clamps spool to Discharge Body to prevent rotation during pump start up Hold-Down, Lift-Out Pipe size	1-1/4"
	Designed "Lift-Out" assebmly load	4700 lbs
H	Discharge body size	8-3/4" O.D. x 8-15/16" long
I	Pitless Unit minimum I.D.	6"
	DISCHARGE CONNECTIONS AND SIZES
J	For Flanged (ASA Std. 150 lbs.):	2” I.D.
K	For Threaded Nipple (NPT):	2” I.D.
L	For Butt Weld (IPS):	2" I.D.
M	For Transition Sleeve (IPS):	2" I.D.
N	Dimension from center of Booster Unit to end of discharge outlet.
	With J Flanged Discharge	9-1/4"
	With K Threded Discharge	4-7/16"
	With L Welded Discharge	6-3/4"
	With M Transition Disharge	15-3/4"
	INLET CONNECTIONS AND SIZES
O	For Flanged (ASA Std. 150 lbs):	2" I.D.
P	For Threaded Nipple (NPT):	2" I.D.
Q	For Butt Weld (IPS):	2" I.D.
R	For Transition Sleeve (IPS):	2” I.D.
S	Dimension from center Of Booster Unit to end of Inlet Connection.
	With O Flanged Inlet:	10-21/32"
	With P Threaded Inlet	11-5/32"
	With Q Welded Inlet	8-5/32"
	With R Transition Inlet	20-5/32"
T	Discharge Body to tank pipe connection:
U	SPOOL ASSEMBLY	4200 lbs.
	Spool design load:
V	Motor Cable tapings through spool (w/cable connectors):	(4) 3/8" NPT
	Maximum allowable	(4) 3/8" NPT
W	Tapping into Pressure Zone:	3/8" NPT
	(Furnished with square head plug)
X	Tapping into Suction Zone:	1"
	(Furnished with square head plug)
Y	Spool to drop pipe nipple connection:	2" NPT
Z	Tank Pipe Size:	5" I.D.

Specifications are Subject to Change Without Notice.

Note: Pitless units conform to the Recommended Standards for Water works, Great Lakes Upper Mississippi River Board of State Public Health & Environmental Managers and Water Systems Council PAS-97 (04) Standards.

COMPONENT MATERIALS
Well Vent - cast iron, green enamel finish.
Cap - cast iron, green enamel finish.
Conduit Box - steel, corrosion resistant coating
Electrical Cable Seal - cast iron, green enamel finish
Combination Hold-Down & Lift Out Mechanism - lead-free galvanized.
Hold-down pipe - steel, corrosion resistant coating
Discharge Body -steel, lead-free galvanized.
Pitless Case - steel, corrosion resistant coating
Spool - steel, lead-free galvanized.
Probe tube - 1" PVC

Note:- Any combination between Drop Pipe and Discharge Outles size is possible, if required
Note: - Maximum rated discharge pressure is 300 PSI

Key No.	Quanity	Description	Ord. No
1	1	Pipe Plug, 2 1/2" NPT	UK50
2	6	Machine Bolt, 1/2-16NCx4 1/2" L	PS221S
3	1	Machine Bolt, 1/2-16NCx3" L	APC7S
4	1	Seal Cap & Plug Assembly	PS350
5	1	Gasket	PS342
6	3	Machine Bolt, 1/2-13NCx2 1/2"L	PS111S
7	1	Retainer Ring	PS341
8	10	Hex Nut, 1/2-13NC	PC433S
9	1	Seal Ring	PS170
10	1	Depression Ring	PS189
11	2	Hen Nut, 5/8-11NC	N75
12	2	Washer	WA75
13	2	Hold-Down Hook	UJ7BH
14	1	Life-Out Pipe & Bail Assembly Note: Must be ordered by description & unit Serial Number	------
16	1	Pipe Plug, 1" NPT-Gavlanized	UN120
17	4	Cable Connectors Note: Must be ordered by description & unit Serial Number	------
18	2	Pipe Plug, 3/8-18NPT	UN122
19	1	Spool (10E0PSF)	UG204
---	1	Spool Assembly w/check valves, inlcudes key no.'s 18 thru 33 (10E2PSF)	UG208
20	2	Hinge Pin	UG29
21	2	Hinge Pin Gasket	SW84
22	2	Rocker Arm-Right Hand	UG147
22A	2	Rocker Arm-Left Hand	UG148
23	2	Valve Spring-Right Hand	UG145
23A	2	Valve Spring-Left Hand	UG146
24	2	Valve Spring Center Support	UG150
25	2	Coupling 1/2-18NPT	PS182
26	2	Nipple 1/2x18NPT	PS181
27	2	Valve Body	UG149
28	2	Rubber Check Valve Facing	UG23
29	2	Brass Washer	UG68
30	2	Brass Nut, 1/2-13NC	TP34
31	2	Check Valve Seat	UG22
32	2	Check Valve Assembly inlcudes key no.'s 27 thru 30	UG323
33	2	O-Ring	UG15
34	1	Pipe Nipple, 4" NPT x 6" L	UK251
35	1	Spool	UG244
---	1	Spool Assembly less check valves. Inlcudes key no.'s 16 to 18, 25, 26 & 35	UG253
36	1	Casing	------
37	1	Discharge Body, FIP discharge outlest standard. Note: Must be ordered by description & unit Serial Number.	UG3
38	1	Tank & Inlet Pipe Assembly. Note: Must be ordered by description & unit Serial Number	------
39	1	Pipe Plug, 1" Galvanized	UN120

DESCRIPTION - ORDERING NUMBERS

Bury Depth in Feet

Pitless Booster for Submersible Pump

Reservoir Tank Size - Ins.

Upper Case Size - Ins.

(W) Welded

Black Upper Case

Watertight Cap

Motor Cable Passages - Sealed

Check Valves: 0 or 2

Size of Drop Pipe in Ins. (4" std)

I		Threaded NPT Std. Connection	Discharge Connections (Select One)
	F	Flange, ASA 150#
		Welded
		Mech. Joint w/transition sleeve

Size of Discharge Pipe - Ins. (4" std)

Length of Reservoir Tank - Feet

Inlet Pipe Size - Ins. (4" std)

Welded

Flange, ASA 150#

Threaded NPT

Mech. Joint w/ trans. sleeve

Elec. Cable Seal(s)

O.D. 3 Wire_______ O.D. Ground Wire_______

Special Provision (X)

UNITS AVAILABLE BY QUOTATION ONLY
5” THROUGH 36” TANK SIZES

EXPLANATION OF PITLESS BOOSTER UNIT
ORDERING NUMBERS
The diagram illustrates the meaning of the various letters and numerals used in Monitor Custom Industrial Pitless Unit ordering numbers. A typical order number and the pitless unit it stands for are shown.

Typical Order Number
6PS810WBWX24F464FS

6	A. The first numeral in the order number indicates the bury depth, in feet, of the unit. Bury depth on all units is measured from the center of the discharge line to ground level. The top of the pitless case extends 12” above ground level as is required by many codes.
PS	These letters indicate the type of pump the pitless unit is designed for. The unit shown is a PS for submersible pumps.
8	B. This numeral indicates the reservoir tank size. 8 is for a 8" I.D. diameter tank.
10	C. This numeral indicates the upper pitless case size. 10 is for a 10" diameter case.
W	D. This letter indicates the attachment to the well casing is a welded joint on 8" - 30".
B	E. The presence of the letter "B" indicates the upper pitless case is black pipe.
W	F. Indicates the unit has a watertight cap.
X	G. Indicates spool passages are closed.
2	This numeral indicates the type of spool which the pitless unit has. In this case it is a spool having two silent check valves. Availalbe with 6 and 8 inch tanks only.
4	H. Indicates the size of drop pipe in inches.
F	I. Indicates the discharge connection is Flanged.
4	J. Indicates the size of discharge pipe in inches.
6	K. Indicates the length of the reservoir tank in feet, and is measured from the center of the discharge line to the bottom of the unit.
4	L. Indicates the inlet connection diamter in inches.
F	M. Indicates the inlet pipe connection is flanged.
S	N. Sealed conduit connection (Optional)

8" Pitless Booster

Latest News

My Account