 |
|
| A |
Screened Well Vent tap size: |
2-1/2” NPT |
| B |
Seal Cap: The Watertight cap bolts to a compression seal ring securing around the pitless case and comes with the screened well vent installed. |
|
| C |
Conduit Tapping size:
Watertight conduit seals for most common cable sizes are available for watertight cap. |
3 ” NPT |
| D |
Depth Tester Tapping: |
1/4” NPT |
| E |
Distance from ground level to top of Pitless Case: |
12” |
| G |
Distance from ground level to top of
Screened Well Vent: |
25-5/16” |
| H |
Pitless Case I.D. size: |
10 ” |
| I |
Pitless Case wall thickness: |
.365” |
| J |
“Hold-Down” - “Lift-Out” Mechanism
Three set screws in a spider atop the “Hold-Down” - “Lift-Out” pipe brace against the interior of the pitless casing, locking the spool in place.
Hold-Down, Lift-Out pipe size (Schedule 80):
|
3 ” NPT |
| |
Designed “Lift-Out” Mechanism load:
|
30,000 lbs |
| |
DISCHARGE BODY - WELDED |
|
| K |
Discharge Body outside diameter: |
13-1/2” |
| K |
Discharge Body length:
8 inch pipe extends from bottom of discharge body
|
15-11/16"
5"
|
| |
DISCHARGE BODY - KWIKONECT |
|
| K |
Discharge Body outside diameter: |
13.197” |
| K |
Discharge Body length: |
15-1/2” |
| L |
Pitless Unit minimum inside diameter.: |
9-1/8” |
| M |
Discharge Connection Tapping size: |
4 ” NPT |
| N |
Pitless Unit to well casing connection I.D.: |
8 ” Weld |
| O |
SPOOL ASSEMBLY
Spool Design Load: |
30,000 lbs. |
| P |
MOTOR CABLE PASSAGES THROUGH SPOOL
Will clear rigid rod parallel to casing |
1-3/4”
1.49” |
| Q |
|
3-3/8” |
| R |
Spool to Drop Pipe Connection: |
4” NPT |
| S |
Pressure zone tapping: 3/8” NPT: |
(2) available |
| T |
Dimension from center of discharge outlet
to bottom of weld nipple: |
12” |
| U |
Overall length of seal cap: |
18-1/2” |
| V |
Dimension from center of discharge to
bottom of discharge body: |
10-1/2 ” |
| W |
Dimension from center of well casing to
end of discharge outlet: |
6-15/16” |
|
Specifications are Subject to Change Without Notice. |
*For Flowing Well spool concept, see Booster Station section.
*Optional flange, weld or mechanical joint available upon request.
Note: Pitless units conform to the Recommended Standards for Water works, Great Lakes Upper Mississippi River Board of State Public Health & Environmental Managers and Water Systems Council PAS-97 (04) Standards. |
|
| |
| COMPONENT MATERIALS |
Well Vent - cast iron, green enamel finish.
Cap & Conduit Box - cast iron, green enamel finish.
Hold-Down Spider - cast iron, green enamel finish.
Hold-Down Pipe, 3” - steel Sch. 80, black.
Pitless Case - steel, black.
Spool - ductile iron, lead-free galvanized.
Discharge Body - ductile iron, lead-free galvanized.
Check Valve Body & Arms - brass.
Check Valve Seat - Brass.
Check Valve Spring - Monel.
Compression Seal Ring & Check Valve Facing - Neoprene.
Electrical Conduit Cable Seal - Neoprene.
Maximum Rated Discharge Pressure - 300PSI
|
|
Contact Us about Industrial Pitless Units by Clicking Here
Water Well Cap | Aluminum Well Cap | Hand Pump | Tank Tee| Pitless Adapter | Yard Hydrant| Pipe Elevator | Pipe Holder | At-The-Well Controls | Water Pump Pressure Switch | Weld Nipple | Snappy, Bulldog | Pitless Unit | Standard Pitless Unit | Custom Pitless Unit | Protective Well Enclosure | Pitless Booster Station | Packaged Pump Station | Water Pressure Booster Station | Booster Station | Custom Turbine Pitless Unit | Hand Water Pump | Well Control System | Water Well Accessories | Ideal Hose Clamps |
6" Industrial Pitless
